INTRODUCTION TO RESEARCH VESSEL LLYR
“Rugged” is the most typical comment by mariners viewing RV Llyr's steel hull, high freeboard, sturdy spars and rigging: inspiring lines and "mighty" beauty that draw from strength. Then follow exclamations of how roomy and bright her interior is when they go below and find how a 16' beam and high freeboard open up 9' of clearance in the interior cockpit/salon/galley paneled in sunny white Baltic birch with teak trim; 27 windows and 7 Moonlight hatches, plenty of headroom and no tight squeezes moving fore or aft. Further comments of appreciation are for her elegant compound round-chined hull, roomy walk-in engine room housing a Perkins/Sabre M90, over-built rugged and beautiful custom storm sails personally designed with Dimension Polyant by Doyle Sail's senior vice president, extended fuel range, and robust mechanical and electronic components more typical of larger commercial vessels.
Research Vessel Llyr (original name “Mother of Perl”) was built in Estonia and Riga, Latvia 2000 to 2001 as the personal vessel of American NOAA benthic mapper, Captain Ben Smith. This heavy displacement vessel is a modified Bruce Roberts 45' steel ketch that is 53' in length overall, 16' beam, full keel with skeg rudder, and 28 tons. RV Llyr contains numerous unique features and custom designs described below. Ben selected the Hop Tai shipyard in Estonia for foundation construction because they combined affordable costs with a unique, traditional construction method that used external frames, wedges and a team wielding heavy mallets to hammer elegant, round chined compound curves into the ship's hull mated to a robust steel deck with expert welding and tight intercostal framing. Traditional Nordic white Baltic Birch panels and teak carpentry completed a roomy and bright interior. After hull construction and the basic installation of the boat's Perkins/Sabre M90 diesel engine, the boat was driven across Baltic waters to Riga, Latvia where high quality spars, heavy fixed rigging, welded stainless chainplates, winches, blocks and electronics were fitted. During her ten years of operation with Captain Smith she sailed the Baltics and historic canals, the English coast and then down to the Canary islands and Tenerife before spending several years exploring the Caribbean both with Captain Smith's family and, at times, chartered under his command. She returned to her home port of Portsmouth, New Hampshire in 2008 for several years of inactivity and then our conservation organization Island Reach acquired her in 2011 for $115,000usd. Over the next year we invested $90,000usd in extensive material upgrades using our own labor where possible. After this comprehensive refit (documented in the vessel's detailed maintenance records and photos) our family and team have operated RV Llyr along the Downeast Maine coast, in the Caribbean working in Dominican Republic, Haiti, Providencia, and Panama and then across the Pacific through the Galapagos, the French Polynesia islands of the Marquesas, Tuamotus, and Societies', the Cooks, Tonga, and Fiji to her working life over the past four years among the remote islands of Vanuatu. Each year Llyr returns to Vuda Marina, Viti Levu, Fiji to her reserved cyclone pit for 7 months of safe storage and then our next refit. Each year, from 2011 forward, Island Reach has expensed on average $7000usd on additional equipment upgrades, costs that are distinct from maintenance, storage, and operational expenses.
Our goal in introducing you to RV Llyr is to convey our deep attachment to the vessel, expressed in our extensive commitment to maintaining here in peak, expedition-ready state. We offer you full transparency about her broad capacities as well as challenges which are all documented in Llyr's detailed maintenance records. Our training in expeditionary blue-water cruising has been to sail the weather, never the clock, and to focus on safety through building into RV Llyr redundancy of high quality components so that, from propulsion, to energy needs, to navigation, communication, sail and safety equipment there is backup in place and ready.
Regarding our timing in offering her on the market: as our volunteer charitable organization Island Reach has rapidly grown in Vanuatu, RV Llyr has fulfilled our goals of exploring remote locations and identifying conservation projects. While we will be using her for limited 2018 expeditions we also recognize she is no longer the best fit as our operations in remote communities in Vanuatu becomes increasingly “in-village” and land based at fixed sites.
RV Llyr is currently in prime condition, carefully maintained with full fuel tanks and state-of-the-art sails ready to launch right now from Fiji, the hub of South Pacific cruising grounds, for the next adventure. For seven years Research Vessel Llyr has given our family and team a rugged, reliable and generous platform for blue-water adventures beyond count. Below we'll go over her systems in detail and, with supporting video, website, and conversation assist you, as Captain Ben Smith did so kindly for us in 2010, in determining if this rugged, uniquely safe and proven steel vessel might be a right match for you, your loved ones or team and your next adventures!
The name "Llyr" is a Welsh God of the Sea. Pronounce her name "Lear", like the jet.
The rays on her bow are symbols commonly believed to impart protection at sea.
CONTACT US BY EMAIL: CONTACT@ISLANDREACH.ORG
We've set up the following format to introduce you to all of Llyr's components and sale and survey information. Click on the "+" sign to open the text box to learn more.
Llyr's elegant round-chined hull is a sweep of compound curves, hand hammered mild steel that draws admiration from those who understand metal boats and this fading construction art. Construction at Hop Tai yard incorporated external adjustable shaping frames, wedges and heavy sledges wielded by teams of shipwrights. She is a significantly modified Spray design. Steel thickness averages 5 ml on the hull growing to 6 on her full keel and 8mm on her keel plate (4 to 5ml on deck). The large rudder is skegg designed and therefore flush to the even keel so that both propeller and vessel are fully shielded from rope snags and blunt impacts. Her shallow draft of 5.5 feet and smooth keel is precisely designed to suit expeditionary island life where atolls often offer fast-water, shallow tidal passes and plenty of rock obstacles. Anchorages in lagoons can snug to the shore as desired to dodge wind or wrapping swell or coral bomies that might damage a bolt-on fin-keel with deeper draft or exposed prop. Llyr's framing, her iron intercostals, are set close in a tight grid that renders her hull stiff. Her ballast is iron embedded in cement and behind all her interior walls the hull is coated with fire resistant urethane foam. You can see on inspection this important feature has blocked any significant rust in hard to reach areas behind walls and tankage, insulates Llyr's interior against both the sun's heat or winter's cold, and renders her quiet to wave action and outside noise.
When we acquired Llyr we went through her entire inner hull below this foam line removing all superficial rust and scale and sealing the metal with a two-pack urethane. Llyr comes with a high quality ($1600usd) Defelsko Positector UTG ultrasound instrument-- certified & factory calibrated in 2017-- with a precision corrosion head that you can use to monitor hull thickness from the inside or out. Our last independent survey in 2017 confirmed the professional survey done by Rick Ferris in 2011 that you can review; her hull is even, well preserved and of high quality with the exception of two pencil size thinning spots we found with ultrasound in her lower chain locker in 2017. That entire hull area, has now been strengthened above original standards with new plate (see picture gallery). This expert welding job took only 8 hours start to finish and cost $480usd. As you may know, one great advantage of a steel boat, along with the security of puncture proof strength, is their ease of plate or deck repair back to original, and in this case, stronger tolerances.
Llyr's last informal rigging inspection was in 2016 by West Rigging of Lautoka Fiji with no signs of crevasse corrosion or significant wire deterioration. A hi-power illuminated jeweler's magnifier is on board for your confirmation. (After changing out her mizzen wires in 2011 we followed traditional advice and sealed terminals with melted beeswax to inhibit crevasse corrosion.) From her large stainless chain-plates welded to the deck to robust wire sizes and numerous stays and shrouds Llyr is considered by riggers overbuilt for strength. Her mast and spars are of high quality and condition, large winches are Anderson and Harkin. We installed a new Harken MKIV furler+stay system for her new genoa headsail as well as a large customized Forespar spinnaker pole and tackle for downwind sailing. In 2011 we also changed out all of her 7 Moonlight hatches, installed hatch safety bars and lazarette bars and locks and replaced her 10 generous custom acrylic cockpit windows with well known Diamond Sea Glaze 3/4” tempered storm-glass and serviced all 27 windows on board. Running rigging is regularly updated as wear indicates, along with blocks and rope clutches, and RV Llyr carries a large supply of backup rode. The vessel's high freeboard and large center cockpit and dual steering stations create safe operating spaces. (We can count on one hand bits of side waves that have slopped onto the stern deck over seven years.) The center cockpit floor is thoughtfully designed for removal allowing for vertical lifting of the engine if ever required for future servicing.
Llyr's foredeck has a broad, open and raised design that allows for both the easy shedding of waves as well as numerous work projects, people or gear to haul. At her stern there are four deep lazzaretts that house dive equipement for 6 [we're supplying 2 tanks and 2+ full dive kits and materials from our sponsor Aqualung USA), compressor, spare ropes, Viking Rescue 8 man Life Raft, Honda generator, heavy charge cables, 6 x 20 liter cans of gasoline, 2 propane tanks, fishing gear and chain etc. Forward, her generous dual hatch chain locker houses gear for Llyr's four anchors, hydraulic windlass, G4 5/16 chain as well as a complete complement of spare sails, 18' Paratech parachute and over 400 meters of heavy thimbled double braight rope for deepwater anchoring or Parachute bridle. Llyr's strong aft davits hold her red 10.5' Achilles FRB-104 Fire&Rescue Dive tender, and the stainless rails carry her Tohatsu 20 hp four stroke motor, Fortress stern anchor, 6 UN military diesel cans and five cans of backup water. Llyr's broad decks have often hauled everything from lumber, massive water tanks (one delivery included 11 x 1100 liter tanks, lumber and hardware!) and cyclone relief materials as well as hosted dozens of conservation workers and divers with lots of room to work, sleep, string a hammock, and play.
When we began to refit Llyr in Kittery Maine and Salem, Massachusetts in 2011 we did not know we were close to renowned Doyle Sail international headquarters. Doyle's chief Vice President, Chris Howe found us by chance and was inspired by our farm families' ridge-to-reef conservation mission and so took us on as one of his projects with later company sponsorship. An avid racing competitor, Chris' goals for Llyr as a rugged blue-water cruiser was to give her as much sail horsepower as possible and build demonstration cruiser sails that were storm tough. To be blunt, Llyr's four primary ketch rigged sails are noteworthy works of art! Chris used a cream colored German dacron, Dimension Polyant (450ap & 410ap) that is heat sized, using hot rollers (no spray adhesives), to lock the warp and weft, and includes strong UV inhibitors. The fabric is stiff and remarkably slow to age. He added reinforcement after reinforcement at load points, and along seams used adhesive tapes alongside triple stitching in a dark brown decorative thread. He put extensive battens in the mizzen , main and staysail that flatten the sails and dramatically tighten Llyr's angle of attack to windward. If you come to Vuda Marina to inspect Llyr you will simply not see another stronger set of sails, all in excellent condition as the fabric is extremely resistant to wear and solar exposure. Alongside her hull, and engine, and roomy bright interior, Llyr's sails are matters of conversation and admiration. In addition, onboard there is a full backup set of white traditional weight and cut sails, and a rubberized orange storm staysail, all in excellent condition and never used. They store forward in a generous chain locker along with a “Code Zero” or Universal Power Sail with an ATN sock and Spectra lines we acquired for deployment in light winds (This sail does require a repair to it's head).
Chris Howe also built for Llyr a large tan Sunbrella bimini with battens and rain collectors for the cockpit. This year we added zippered extensions to the bimini which both extend rain protection and can be turned into full water collecting gutters for Llyr's 3 large SS water tanks.
Captain Smith funded the vessel's construction with a family inheritance. With his extensive experience as a NOAA ship's captain, he fulfilled his wish list with strong, proven equipment. Llyr's engine is a Perkins/Sabre M90 4 cylinder naturally aspirated diesel, (output at shaft 80hp) a heavy engine renown for durability and minimal maintenance. The engine is housed in a generous walk-in engine room making for easy access and maintenance. She has always fired on first rotation and burns zero oil. Her transmission is an oversized Hurth HSW 450-A2 connected to a high-end Aquadrive coupling that dampens vibration and wear. We have confirmed with a designer that her brass propeller is precisely matched for efficiency in size and pitch to both engine and boat size/length. In 2011 we replaced her European drive shaft with one turned at Rose's Marine in Gloucester, Mass. Last year when changing out her cutlass bearing we also replaced her oil-bath stuffing box with a state of the art PSS dripless carbon/stainless shaft seal (stuffing box)—no leaks and runs cool to the touch. (At the same time we swapped out the shaft cutlass bearing behind the prop—standard maintenance) The engine has a high output (100amp) alternator (she carries a spare new backup 100 amp alternator) and three raw water coolers for coolant, engine oil and transmission. Like everything on a Perkins, these Sabre coolers are made rugged with thick pipes. When required the engine also runs a hydraulic windlass pump on an electric clutch which drives the chain gypsy and capstain of a Simpson/Lowrance V3000 windlass with remote electronic controls fore and aft. In 2017 we completely rebuilt this windlass replacing all drive gears, shaft, ratchet and seals returning the unit to “as new” condition. Also, in the last year we replaced her engine raw water pump (standard wear) and all three coolers have been limeaway cleaned and the coolant is fresh. The dual helm throttle controls are electronic Mathers with a central Mathers Commander servo controller; a proven workhorse system common for decades on much larger vessels (and still in production).
Maintenance records confirm that we have babied this Perkins “fifth iron sail” using Mobil Delvac and Shell Rotella 15W40 heavy duty diesel oil and fresh ATF in the transmission and windlass. The four injectors were inspected and serviced last year as routine maintenance. Dual Volvo/Pentax & Parker/Racor centrifugal fuel filters use 10 micron cartridges—one active filter and one backup that draw from dual 440 liter stainless steel diesel tanks and 100 liters on deck in UN military tan gerry cans. All diesel is carefully Baha filtered and treated with algicide to protect the engine, no exceptions. At her happy running rpm of 1800 to 2100, RV Llyr burns 3 to 4 liters of diesel per hour at an engine only speed of 5.5 to 6 knots which gives her a fuel range—along with the 100 spare liters on deck-- of 1347 nautical miles. Llyr's robust engine profile complements her comprehensive sails and has offered us a range of backup, redundant security options lending agility and confidence to adventure after adventure over the years that include our annual windward 500nm return sail from Vanuatu to Fiji. Over her 16 years of operation the motor has just passed 5247 hours of run time which Perkins mechanics consider less that half of her running time to rebuild. And finally, Llyr carries significant OEM spare engine stores—never needed—that include starter motor, starter solenoid, coolant pump, raw water pump, new replacement high amp alternator, fuel lifter, complete hose kit, gaskets and large supply of belts and filters. Everything needed for our families' security on blue-water expedition, ready to go. And she has always fired on first compression.
ELECTRONICS & COMMUNICATION
Two years ago we replaced the vessel's NMEA183 network with a NMEA2000 network B&G Triton package. Plug and play components feeding the trunkline and two glass/4 color display screens, include Course, Radar, Depth & Speed Over Ground, GPS, True & Apparent Wind, Water Temp and AIS data. There are two VHF radios; the Standard Horizon GX2100 Matrix provides AIS data to the network and the ICOM IC-M504 is backup and connects to a remote handset in the external cockpit. An Amek NK80 translator converts AIS data to NMEA2000 format. An Actisense NGT-1USB converts NMEA2000 to USB format as Llyr's navigation is configured for PC and Coastal Explorer Navigation software. The receiving laptop computer lives below on the navigation table (we travel with two additional Thinkpad computer backups) and projects image and mouse control through HDMI and USB to a 24” Asus Pro-Art Wide Color Gamut 1920x1200 full HD video format 1080p screen above at the interior navigation station. This large screen can configure multiple overlapping display panels as desired.
Llyr's original 2kw Raytheon radar and cables were replaced 2011 with a Si-Tex, Koden 4kw unit (twice the range). The Koden antennae can see up to 36 miles. The unit is sophisticated and sensitive with numerous tracking features and filters.
Coastal Explorer from Rosepoint Navigation is non-proprietary for maps-- we use Italian C Maps and Google geo-referenced maps (Admiralty maps are another option). The software is agile and can overlay multiple data sources on different sub-screens on the monitor. We commonly overlay radar onto our route (+AIS) displayed on dual C-Maps and Geo-referenced Google Earth map screens giving us high mapping reliability and position confirmation. The computer handles all contemporary navigation, quilting and plotting tasks including speed and distance estimates to goal and displays a wide array of instrument options from AIS data to Apparent vs True Wind, heading, distance to goal etc. The BG Triton system further includes two independent glass, color display screens (one interior and one exterior) that are programmable with up to 8 data windows per screen including wind speeds, course, depth, boat speed etc.
Along with the two VHF units Llyr holds an ICOM IC M710 SSB transceiver with AT-130 tuner in excellent condition and carefully grounded and choked. The SSB is integrated with a German Pactor SCS PTC IIUSB Modem that interfaces with the ship's computer to allow send/receive emails at sea via SailMail. We have put carefull attention into the radio system's grounding, chokes, RF drains and antennae length. When on expedition we regularly speak with cruisers, exchange emails, and gather weather from New Zealand's Gulf harbor radio and other nets and chat across thousands of nautical miles from Vanuatu to Fiji, Tonga and the Torres Strait. A Motorola sat phone backup has completed Llyr's communication redundancy.
ELECTRICAL & CHARGING
Research Vessel Llyr has shipwide dual 12v and 110V systems, wall plugs and charge ports all with breakers and fuses which, along with a Freedom 2000 watt inverter/charger are managed by a Heart Interface Link 2000-R controller/regulator that provides full digital volt/amp & amp/hour charge information for two banks. Llyr's six Trojan T105 6v lead/acid house batteries (running parallel and in series) are three years old and not allowed to drop charge below 12 volts; no exceptions. Total house capacity is 1350ah @ 20hrs (or 1110@ 5 hrs) Her large Caterpillar 1400 CCA engine/backup battery was purchased in 2017 ($500usd).
Ship's power and battery charging can be supplied three ways; 1) by shore power (galvanic isolator protected) using an on-board 220v to 110v transformer; 2) by the engines 100amp alternator (a new backup 100amp alternator is on-board) or; 3) by the ship's 2000watt Honda inverter generator's 110/12v output. The Heart-Interface system is a smart charger, monitors for reverse polarity and can equalize the batteries when needed to restore their storage capacity. On board is a new backup 1000watt inverter.
All of the ship's lights, including interior, deck, navigation, steaming and anchor have been changed out for low draw LED's. Llyr carries a silver/silver chloride half cell anode tester that fits to a multi-meter and confirms the mild steel hull and her 22 zinc anodes at a stable .8v is properly anode protected and carries no stray current, poor grounds or reverse polarity.
AUTOPILOT & NAVIGATION
Llyr's internal and external wheels each operate a manual in-line Sleipner hydraulic helm pump which then drives a brass and stainless ram at the rudder. The ram was serviced and all seals replaced in 2017. The external helms pump seals were also serviced in 2017. Two Comnav rudder gauges indicate rudder angle at both helms. The external gauge was replaced in 2017 ($350usd)
Llyr's hydraulic autopilot is a COMNAV 2001s autopilot and controller—a well known, rugged industry workhorse still in production. The 2001s is designed for sailboats and has a wide range of settings for speed, pitch and yaw to adapt to changing sea states. Compass headings are input from a sensor under a large Derigio card compass. Heading coordinates are fed from the controller to an electric hydraulic pump next to the Sleipner ram at the rudder. The hydraulic pump was replaced 4 years ago and a new heading sensor was fitted to the compass in 2015. The Derigio compass was re-magnetized in 2012. The external helm has its own large gimballed fluid compass.
There is a complete heavy stainless steel hand tiller system that ports through the aft deck to the rudder (stored and never used) as backup to the hydraulic system.
Primary anchor is a new technology Manson Supreme that, like a Rocna, does incredible work.
Secondary anchor is a traditional CQR
Third anchor is a tough Aluminum Fortress which often serves as a stern anchor
The fourth anchor is a small tender anchor
And the fifth anchor is a backup large and heavy no-name spade anchor
Anchor rode includes 100 meters of G4 5/16 chain and 150 meters of G3 5/16 chain. There are 75', 150' and 250' 8 strand plaited nylon brait lines with stainless steel thimballs (17,000lb working load) along with new docking lines and snub lines with stainless snub-hooks and hardware and chafe gear.
The hydraulic windlass is Sampson/Lowrance Pacific V3000 with both forward and aft electronic controls. The Windlass head was completely rebuilt this year replacing all planetary cogs, seals, shaft and shims returning the unit to “as new” condition ($1000usd). The windlass can handle both chain and rode which feed through two heavy bow rollers on the stainless bowsprit allowing for dual anchor deployment if desired in strong conditions. Deck rope cleats, like Llyr's chainplates, are powerful.
Jacklines fore and aft with 8 PFDs with built in harness and stainless steel clipped tethers
3M deck grip strips
LED Deck lights fore and aft
Additional Mustang life vests and type 1 jackets
Viking, RescYou 8 man life raft in sealed valise
Forespar MOB floating strobe & Forespar MOB pole
ACR category 1 hydro-release Global Fix Pro EPIRB, registered with USCG
2 x floating VHF radios
2 windshield wipers and defoggers
ACR Ditch bag stocked
large complement of marine flares alongside two heavy European pistol army surplus flair guns with potent flares
Lifesling MOB and throw ropes
Fireboy Propane sensor
Spare stainless steel tiller steering system
4 ways to pump bilge and seawater: 2 Jabsco 3000 Submersible Bilge Pumps on automatic in fore and aft bilges, 1 Whale Gusher 30 Manual Bilge Pump in the engine room, and a raw water Y-valve that converts the engine's raw water intake into an emergency bilge-pump.
Stainless steel bars and locks for all lazarretts and SS hatch bars that prevent intrusion if you happen to anchor where night security is a concern.
A ship's design has a lot to do with her safety parameters. RV Llyr's sail/hull/keel Spray design and weight lean stiff into her sails, track steady and limit pitch and roll. A Ketch rig provides five “points of effort” moving the yacht forward at bow, staysail, main, mizzen and propeller. These five adjustable points of effort provided many options for steadying the yacht's track as she interacts with wind angle and often complex sea states. Safety at sea begins with a well settled vessel responding with lively, predictable motion to ever changing conditions. Llyr's generous center cockpit is stable and dry, her high freeboard rarely takes any wave slop aft. Shipwide there are many well placed handholds both above and below. And then there is Llyr's stiff steel hull which responds lightly to large seas alongside her overbuilt spars, rigging and storm sails that offer stable confidence in rough conditions.
INTERIOR LIVING SPACE
Those entering Llyr's cabin for the first time tend to remark on the unusual spaciousness of her high ceilings and wide beam and how bright the interior is with white Baltic birch panels trimmed with teak along with 7 Moonlight hatches and 21 windows and ports! With her interior cockpit integrated with the salon Llyr measures 9+ feet from sole to cabin top where seven cockpit windows with new tan sun screens throw warm light below! The sole is panels of teak veneer with blond piping. Forward cabins are plush double berth V's with desks and clever folding chairs. We added a removable bunk to the starboard cabin allowing Llyr to sleep 9 (We have often hosted many more on-board for the night). There are two generous heads with waterproof shower floors, forward is electric and aft is manual. Two Scandvick sink faucets double as showers and all drains to teak grill pans. All hot and cold plumbing is Whale 15mm with SS screens throughout. There's plenty of room in the heads for storage or to hang dive gear. New low draw fans are all about and Llyr's insulated hull shields the vessel interior from the midday sun.
The two heads are piped with new plumbing hose and ready to receive a holding tank that, in the US, was mounted in the engine room. That 70 gallon tank is now removed to allow for greater space. The large engine room houses Adler Barbour Super Cold Machine refrigeration as well as Isotemp hot water supplied by either the engine's coolant or direct electric element.
There is a larger navigation table with extensive storage and an oversized map drawer and then aft is a 7' pilots berth and further aft the captain's cabin with double bed and short couch/bunk trimmed in plush fabrics.
Across from Llyr's salon seating, convertible bunk and teak folding leaf table is a lovely stainless steel Dickinson Marine Antarctic Diesel Heater with a glass burner window (list$900); useful when sailing the US Northeast coast and it would serve well those headed for New Zealand.
While many describe life on a boat as learning how to operate in small spaces that has not been our experience with Captain Smith's generous design that he built anticipating both family and commercial use and that we at Island Reach have enjoyed as a working conservation vessel and home for our family. RV Llyr is roomy, pleasurable, bright and with huge amounts of storage both in her lovely nordic and teak trimmed cabinets and below every teak sole panel.
Refrigeration is provided by an Adler-Barbour Super Cold Machine that cools a heavy cold plate. Recent servicing includes a new cooling fan and diagnostic panel. The compressor has not needed recharge in seven years of operation. This year we have added an additional new Dometic freezer for deep cold storage of meats, etc.
The Plastimo 3000 three burner stove and oven is gimballed and fiddled and draws from 2 external propane tanks.
Water is stored in three stainless steel tanks below the soles and totals 1300 liters. The dual SS galley Scandvick sinks have three faucets to provide 1) 0.5 micron and carbon filtered water for drinking (Pentek CFB-PB10 Carbon/Fiber block cartridges), 2) direct hot & cold tank water and 3) sea water for washing.
Storage for expeditionary foodstocks is extensive both in the galley and under the salon couches and three overhead food hammocks. The teak table has two leafs that fold down and is fiddled as are all counters. The cockpit also has a folding teak table and built in cooler storage. Along with a Magma Nestable 10-piece stainless steel cookware set, the ship has a small Cuisinart, silicone bread pans, and more kitchen implement. Counters and passage are thoughtfully designed for bracing and control when cooking in active seas.
On the aft deck is mounted a propane Dickinson Sea-B-Que with stainless grill plates
spares & resources
Extensive foldered technical manuals and DVDs on all equipment with notes on where to acquire spares or guidance are on board alongside the ship's detailed maintenance log. In addition Llyr carries classic volumes including Chapman and Bowditch, plenty of Nigel Caulder, Birch on weather and radar, anchoring with the new technology, storm sailing, meteorology & climatology, maintaining metal boats, diesel engines, electronics, PADI diving and a number of books on paper and electronic navigation. The ship's large map drawer carries detailed paper maps of the SW Pacific and mapping tools and Jimmy Cornell's updated pilot charts and navigation tools. There are bug nets and wind scoops for the hatches.
Numerous spares are onboard in addition to those listed for the engine: two backup gps units, portable wind and depth meters, a spare inverter, smart battery charger, antennae amplifiers, a transformer and specific seals, filters, circuit boards, carburetors, raw and fresh water pumps and service rebuild kits. 8 years of experience in three oceans and targeted expensing have refined RV llyr's Spares Lockers and toolkits to what is needed on remote expeditions. There is a locker for raw and fresh water plumbing with rebuild kits, fuel line repair parts, locker for electrical and Blue-Sea components, locker for paints, rust control and materials, and a lockers engine spares each with specific backup parts like carburetors, fuel lifter, coolant pump, high amp alternator, and bins for special tools and plenty of fuel/oil filters and raw water impellers. There is a locker for sail repair and a large supply of replacement lines in 8 rope bags. Then there are numerous hard to find materials including gaskets, O-rings, and diverse glues and sealants including Splash Gaurd emergency repair epoxy. In addition there is a robust tool kit on board of comprehensive sockets, spanners, saws, drill, 2 angle-grinders, orbital sander, cutters, pullers etc. This includes the high quality Defelsko UTG ultrasound metal thickness gauge and stray current anode. Llyr carries a climbing harness and belt pack for work on the spars and various foul weather clothing and footwear. We have done our best to make these stores comprehensive and compact. Llyr is rugged and roomy and she can easily accommodate the many spares esseential to safe passagemaking.
We have operated Llyr with six Catalina SCUBA tanks and can offer her with two tanks along with three completed dive kits including numerous mechanical and wetsuit spares. The compressor is a Coltri MCH-6 we bought new in 2011. This year we replaced the complete OEM compressor head ($2000usd) which is driven by a 5hp Honda engine. There is a full complement of cartridges, oil etc.
Llyr's dive tender is a 12.5' Defender First Responder, hypalon inflatable with a 20hp Tohatsu four stroke engine and Racor 120R-RAC fuel separator. With a rigid aluminum floor and inflatable keel the tender planes, moves fast and can field 4 divers and a driver or 8+ persons. When underway the tender lifts onto Llyr's heavy steel davits.
Llyr carries an articulated 24” Asus HDMI VS24A monitor with 170 degree view angle (this screen is also backup for the navigation screen), and with Bluetooth, you'll have great cinematic experiences. There are hammocks for the foredeck and ship's games. Llyr carries a wakeboard that the tender pulls, 2 Blue Water fishing trolling kits with 500lb strength parachord, big lures and spares, a Dagger Torrent kayak and a Sea-B-Que barbecue with stainless steel grill plates.
our approach to metal boat maintenance
Corrosion control is basic maintenance with metal boats. When on expedition, Llyr will develop emergent superficial rust spots on her topdeck where paint chips and around some of her windows. Our management of rust is to move on it quickly, grind out the area with a flap-disc on an angle grinder and treat the spot with phosphoric acid that converts the rust to hard, black ferric phosphate. We then prime the site with Interlux Primacon and topcoat with International Toplac one-pack marine enamel. This is a fast process using high quality materials.
In September 2017 RV Llyr received new coats of dark red Transocean 2.71 hard ablative bottom paint, side hull paint in International Toplac high gloss 1 pack marine enamel Donegal Green (British Racing Green) with cream bootstripe and deck paint in International Toplac high gloss Marine Enamel custom light tan.
We have limited the use of fairing fillers that might conceal emerging rust. Quality one-pack marine enamels are simple to apply, lower cost, and significantly less toxic to handle and breath compared to two-pack epoxies. Research Vessel Llyr's deck is easy to treat and maintain in a fashion familiar to commercial boats and fitting to Llyr's rugged style and activities. We've seen too many vessel's, both metal and plastic, where overlays like teak decks and fillers conceal advanced corrosion or water intrusion. We are very pleased with RV Llyr's open design that allows for pro-active maintenance regimes.
Corrosion protection also means insuring that a metal boat's electrical grounds are sound and the vessel is not exposed to stray electrical current from outside sources in a marina. Llyr carries a silver/silver chloride half-cell testing anode to monitor hull voltage. Shore power is fitted with a galvanic isolator and her power state is continuously monitored by the Heart Interface Link 2000-R charge controller and breaker/fuse banks which would indicate reverse polarity. Llyr also carries spare large sacrificial zinc anodes “fish” on wires to place for protection between her and any other vessel.
Where Llyr's hull is inaccessible due to interior walls and equipment her steel hull, frame and deck plate has been treated with flame retardant foam over primer to just below the waterline (including both heads) that has been effective at blocking corrosion. Most areas under the soles and below this foam line are accessible and have been cleaned and treated by us with sealing epoxies (Preprime 167) and Interlux Primacon Underwater Primer. Areas that may become wet and lift sealants—such as under the galley sinks and in the engine room—we treat as needed with aerosol corrosion inhibitors such as CRC's Lanocote. All electrical connections are also treated with corrosion inhibitors.
From both inside the hull and outside we can quickly monitor all areas, including those few that are hard to reach—like around the heads—with the ship's premium quality Defelsko Positector UTG Ultrasound unit. With these procedures Llyr's hull is understood and maintained in excellent condition. Llyr's design is intelligently accessible for rust control. There are no teak decks harboring un-seen runaway rust!
Rust control and metal work is relatively quick, low cost and non-toxic compared to the challenges of plastic boats that suffer electrolysis of gelcoat, UV sun-rot, embrittlement, hard to detect water intrusion into foam cores that weaken hulls and structural integrity and the long-term structural damage that can come with object or reef strikes at sea. In addition, RV Llyr's maintenance is spared the high toxicity and costs of both repairing fiberglass and maintaining two-pack paints and gel coats.
In the South Pacific, like in the Netherlands, metal boats are common, well maintained, and prized for their strength and security. We see many metal boats under fine maintenance regimes that are forty and fifty years old. We have insured that RV Llyr is on track to be one of them.
PRICE & CONDITIONS OF SALE
Research Vessel Llyr's price is a fair/low $194,000usd.
RV Llyr is in Fiji as a "Yacht-in-Transit" (12 month rotation clearance) and therefore is offered as an "offshore sale". This is a simple and conventional transfer process. We have signed onto an exclusive relationship with a superb, friendly and supportive local brokerage Nautilus Yacht Management who's seasoned director Anna Manach runs a skilled, supportive and thoughtfully different person-centered yacht brokerage. Learn about her approach here:
RV Llyr's homeport is Salem, Massachusetts (near where our family home, and farm Berkshire Sweet Gold Maple Farm, is located). She is registered and documented with the US Coastgaurd as #1090100. An "Abstract of Title Search" confirms she has no leans or debt of any kind against her and this USCG documentation serves as her Title for Transfer to a new owner. She is currently insured by Northern Reef through Edwards/Williams.
We understand there may be some distance and schedule challenges--- as well as possible advantages---to your considering purchasing a vessel in Fiji. To that end we will be attentive to your concerns and work closely with you. And we have chosen to ease this process and your costs by positioning RV Llyr's price attractively at $194,000usd which is $50,000usd dollars below her 2017 Condition & Evaluation Survey combined with a fair/low estimate of her additional equipment and stores value.
Research Vessel Llyr underwent a Condition and Evaluation Report on September 11, 2017 conducted by Dover Marine, Director and Master Mariner Douglas E. Worthington, MNI,M.A.I.M.S. in Lautoka, Viti Levu, Fiji. Dover Marine is a reputable commercial vessel surveyor with expertise in steel vessels. RV Llyr was given a value of $225,000usd (full report is below). This was a vessel only Condition and Evaluation Report that did not include RV Llyr's 2018 Toplac International paint, additional equipment that includes new 2018 Achilles dive tender and 20hp Tohatsu motor, compressor, dive tanks and related gear, Honda generator, and additional safety equipment including parachute, full spare sail set, etc. and extensive Spares Lockers and tools all with estimated value in excess of $20,000usd. In addition RV Lyr currently comes with pre-paid in water berth through October 2018 and pre-paid cyclone pit reservation at Vuda marina from November through May 2019.
Step 1: Contact both us and Anna Manach at Nautilus Yacht Management to ask questions and consider options. Review all available information photos, video, records and surveys and request RV Llyr's detailed maintenance logs. If you would like to visit the vessel and tour with Anna, RV Llyr is located 15 minutes by cab from Nadi International Airport, Fiji at Vuda Marina (www.Vudamarina.com) which has guest bungalows.
Step 2: An offer made and agreed to would result in a cleared deposit and signed agreement of sale posting that RV Llyr is under offer. At this time sea trials are an option, and/or further survey and inspection.
Step 3) Acceptance of vessel and final price with boat sold and title transferred. For an Offshore Sale/Transfer new owners are supplied with a letter of permission from the current owners for Immigration clearance to sail Llyr out of national waters to your next port of call where the vessel clears in under your new ownership. With vessels returning to Fiji as a yacht-in-transit with a new owner this commonly involves return passage to French territory Futuna island (120nm to the North of Fiji). Otherwise you may be moving on in your passagemaking to the port of your choice and/or importing and registering RV Llyr in your home country or another favorable country. Nautilus Yacht Management has creative solutions and delivery skippers who can assist if needed.
Our goal is to provide you abundant and transparent information and work closely with you every step of the way. (We are both a family and a charitable organization, conservation scientists working as volunteers in collaboration with The Ocean Foundation.) Our family and team hold deep attachments to RV Llyr. She has been our adventurous home at sea and work platform for 8 years. Llyr is available now and easily accessible at lovely Vuda Marina for your inspection with our support alongside her friendly team of caretakers. And when the time is right for sea-trial we will be there to sail with you and support your full understanding of RV Llyr and appreciate her superb capabilities.
We can provide Llyr's detailed maintenance records from 2011 to present as a PDF.